對于經常使用河北升降貨梯http://www.qdysj.net/的朋友來說，河北升降貨梯主要由導軌架、起升機構、物料平車、附著裝置、安全裝置及電氣設備等組成。同時大家也知道選購河北升降貨梯的時候，其安全性是最重要的。河北升降貨梯要承載一定量的物資和人身，跨越的高度也是很大的。
1、河北升降貨梯導軌架采用2根10號槽鋼作為導軌架標準節主肢，用1英寸管為腹桿。每節標準節的長度為2500mm，在滿足強度要求的前提下，將標準節設計為片式結構，以方便運輸和安裝。每兩節標準節之間用折彎聯板在槽鋼內側進行聯接，槽鋼外表面必須平直，以確保物料河北升降貨梯運行平穩。
Shandong cargo lifter guide frame with two on the 10th channel as a guide rack standard section main limb, with 1 inch tube webs. The length of each section of the standard section of 2500mm, to meet the strength requirements under the premise of the standard section is designed to piece structure for easy transportation and installation. Each section between the two standards associated with the bending plate in the inside channel to connect as the outer surface of the channel must be straight, in order to ensure the smooth running of material Shandong cargo lifter.
  
2、河北升降貨梯起升機構放置在導軌架標準節底節上，以方便其安裝、接線、調試和日常維護等工作。在標準節的頂節上設置有一個定滑輪，起升鋼絲繩經其穿繞后向下拉伸并固定在液壓升降機上，以提升物料平車，運送施工物料并將施工層的廢料等運至地面。
Shandong cargo lifter lifting mechanism is placed on the bottom rail frame section standard section, in order to facilitate its installation, wiring, commissioning and routine maintenance work. It is provided with a fixed pulley lifting rope through stretching and fixed on a hydraulic lift after winding down after it, to enhance the material flat car, transport of construction materials and construction waste layer on the top section of the standard sections, etc. into ground.
   
3、河北升降貨梯http://www.qdysj.net/起升機構選用減速電機，電機軸線與輸出齒輪成L形輸出，使起升機構體積達到最小，方便布置及運輸。同時設置一級開式傳動齒輪，一方面可增大減速比，另一方面也可使減速機位置相對于卷筒中心向后移動，可使起升機構整體安裝便捷。河北升降貨梯主梁上設有導向滾輪。為減小滾輪壓力，同時為了保障提升河北升降貨梯護欄有一定的防護高度，將上下導向滾輪距離設定為其結構范圍內的最大值，使物料平車有一定的導向高度，使車輪受力合理，運行更平穩。
Shandong cargo lifter hoisting mechanism chosen geared motor, the motor axis with the output gear to the L-shaped output, allowing the lifting mechanism to a minimum volume, convenient arrangement and transportation. While setting level open drive gear, one can increase the speed reduction ratio, on the other hand also allows gear position relative to the roll center moves backward, lifting mechanism allows easy installation as a whole. Shandong cargo lifter main beam with a guide wheel. To reduce the pressure roller, and in order to enhance protection of Shandong Huoti have some protective fence height, distance between the upper and lower guide roller is set within a maximum range of its structure,the material has a certain orientation flat car height, the wheel force reasonable, run more smoothly.