1、先將固定升降機http://www.qdysj.net/工作油缸伸進方檔塊孔內，將螺帽擰到底，使螺帽與方檔塊靠緊再旋緊蝶形固定螺絲，然后將壓高管端部快速接頭活動部外套向后拉，并套在工作油缸接頭上手放松，活動部份恢復到原位即自行扣上，再將泵體上的放油螺釘旋緊即可工作，同樣當工作完后將放油螺釘放松，工作缸就會自動回縮。
First fixed lifts operating cylinder bore into his side of block, tighten the nut in the end, so that the nut and the side of block abutting then tighten the screws butterfly, and then press the ends of quick connectors executives coat to the active portion after the pull, and set to get started in the working cylinder joints relax, moving parts back to the place that is self-buckle, and then pump the oil drain screw can be tightened on the job, the same job after the discharge of oil when the screws loosen, cylinder will automatically retract.

2、固定升降機平彎時打開上花扳將夾板模頭部裝進工作油缸頭，根據所彎排的厚度，選擇模板與鋁排或銅排一起放進夾板模頭中，然后壓緊夾板將兩只輥柱的槽寬對應向著鋁排和銅排厚度，并且放入相應的尺寸孔中，再將上花板蓋上，立彎時打開上花板，將直角模頭裝進工作油缸頭部，在下花扳孔插上兩只銷子，再將上花板蓋上，鋁排或銅排放在銷子與直角模頭之間即可工作。
Open the flower head pull the plywood mold cylinder head work put into fixed lift-bending, depending on the thickness of the curved row, select the template with aluminum or copper discharge into plywood die together, and then the two clamping jaws corresponding column width roller toward aluminum and copper thickness row, and into the appropriate size hole, and then spent on board cover, turn spent on board when the vertical bending, the work put into the right angle die cylinder head, spend the next two pin pull plug hole, then spent on board cover, aluminum or copper exhaust emissions can work at a right angle between the pin and die.

3、固定升降機http://www.qdysj.net/使用時如出現空打現象，可先旋松泵體上的放油螺訂，將泵垂直起來頭向下空打幾下，然后而旋緊放油螺釘，即可繼續使用，在有載荷時切忌將快速接頭卸下。本機是用油為介質，必須做好油及本機的清潔保養工作，以免淤塞或漏油，影響使用效果。
Such as when using a fixed lift runaway phenomenon, can put the oil set to loosen the screw on the pump, the pump vertically up and head down a few dozen empty, then drain and tighten the screws, you can continue to use, there is avoid the quick connector when removing the load. This machine is oil as the medium, we must do the work of cleaning and maintenance of oil and the machine, in order to avoid blockage or leakage affect the results.